Difference between revisions of "PhiX:Plaque assay"
(→Summary) |
(→Summary) |
||
| Line 7: | Line 7: | ||
5 g yeast extract<br> | 5 g yeast extract<br> | ||
10 g NaCl<br> | 10 g NaCl<br> | ||
| − | 15g agar (if plate agar) | 7g (if top agar) | + | 15g agar (if plate agar) | 7g (if top agar)<br> |
Make up to 1 litre in distilled water and autoclave. After autoclaving:<br> | Make up to 1 litre in distilled water and autoclave. After autoclaving:<br> | ||
CaCl<sub>2</sub> to a final concentration of 2 mM,<br> | CaCl<sub>2</sub> to a final concentration of 2 mM,<br> | ||
MgCl<sub>2</sub> to a final concentration of 10 mM.<br> | MgCl<sub>2</sub> to a final concentration of 10 mM.<br> | ||
| − | (for these use hydrated crystals as anhydrous powders do not dissolve effectively).<br> | + | (for these use hydrated crystals as anhydrous powders do not dissolve effectively. Matching concentrations should prevent diffusion of salts away from one layer).<br> |
| + | |||
| + | Top agar can be retained at 50-55 centigrade for short term storage and deployment. It is recommended to prepare top agar in small batches to prevent cross-contamination. Microwaving is possible but not extensively tested in our lab.<br> | ||
| + | |||
| + | '''Plate and Agar Preparation'''<br> | ||
| + | 1. Set up a water bath to 48 centigrade<br> | ||
| + | 2. Poor plates in the usual way using the plate agar solutions. No antibiotic is usually required so you can do this with quite hot agar taking all the usual precautions.<br> | ||
| + | 3. Add as many tubes as required, each capable of holding 4ml of top agar. These tubes do not need to be labelled.<br> | ||
| + | 4. When the tubes are warm, use a serological pipette to add 4ml of molten top agar to each tube. (You can use a 10ml pipette and overload to 12ml = 3 * 4ml to dispense)<br> | ||
| + | 5. Allow the top agar to equilibrate to the water bath's temperature. (Hotter and you may kill the bacteria. Cooler and the agar may prematurely solidify.) | ||
'''Plating Procedure'''<br> | '''Plating Procedure'''<br> | ||
Revision as of 06:42, 20 February 2017
Summary
This protocol is usually used in conjunction with serial dilution of a stock solution of phage for enumeration of phage titer. But it can also be used with any phage-containing input. With thanks to the Wichman lab for setting me up with a good protocol for this early on.
Media Preparation
The usual media for plating is lysogeny broth (LB). Remember that this is not a defined media (so you should attempt to minimise batch effects for reproducibility) and it comes in Lennox and Miller varieties. The appropriate type is Miller which contains 10g/L of sodium chloride (versus 5g/L in Lennox). Both plate (base layer) and top agars should be prepared. For one litre:
10 g Tryptone
5 g yeast extract
10 g NaCl
15g agar (if plate agar) | 7g (if top agar)
Make up to 1 litre in distilled water and autoclave. After autoclaving:
CaCl2 to a final concentration of 2 mM,
MgCl2 to a final concentration of 10 mM.
(for these use hydrated crystals as anhydrous powders do not dissolve effectively. Matching concentrations should prevent diffusion of salts away from one layer).
Top agar can be retained at 50-55 centigrade for short term storage and deployment. It is recommended to prepare top agar in small batches to prevent cross-contamination. Microwaving is possible but not extensively tested in our lab.
Plate and Agar Preparation
1. Set up a water bath to 48 centigrade
2. Poor plates in the usual way using the plate agar solutions. No antibiotic is usually required so you can do this with quite hot agar taking all the usual precautions.
3. Add as many tubes as required, each capable of holding 4ml of top agar. These tubes do not need to be labelled.
4. When the tubes are warm, use a serological pipette to add 4ml of molten top agar to each tube. (You can use a 10ml pipette and overload to 12ml = 3 * 4ml to dispense)
5. Allow the top agar to equilibrate to the water bath's temperature. (Hotter and you may kill the bacteria. Cooler and the agar may prematurely solidify.)
Plating Procedure
Add 100ul
Recommended Reading
I recommend checking:
Kropinski, A.M., Mazzocco, A., Waddell, T.E., Lingohr, E. and Johnson, R.P., 2009. Enumeration of bacteriophages by double agar overlay plaque assay. Bacteriophages: Methods and Protocols, Volume 1: Isolation, Characterization, and Interactions, pp.69-76.
for more details of the plaque assay and variations thereon.
